Muc-off Ultimate Tubeless Setup Kit

A kit complete with every essential needed to join the tubeless revolution. Five different kits for all kinds of bikes. Our Ultimate Tubeless Setup Kit is a one-stop shop for everything you need to make the switch with your tubeless-ready wheelset. 

SEE IT IN ACTION

Going tubeless? Our Ultimate Tubeless Setup Kit is a one-stop-shop for everything you'll need to make the switch. Just make sure you've got tubeless-ready wheels and tyres

The Muc-Off Ultimate Tubeless Kit contains everything needed to get a tubeless-ready wheelset set up and ready to roll. Each Kit contains a Muc-Off Tubeless Rim Tape, Seal Patches, 2 CNC-machined black tubeless Valves and 2 pouches of No Puncture Hassle Tubeless Sealant.

Features

• Everything you need in one simple kit

• Say goodbye to carrying spare tubes!

• Check our how-to featuring the Deakinator

EVERYTHING NEEDED TO GET SET UP AND READY TO ROLL

Our Ultimate Tubeless Setup Kit is a one-stop shop for everything you need to make the switch with your tubeless-ready wheelset.

WIDE RANGE OF SIZES AVAILABLE

Kits available for road, gravel and CX to enduro, trail and downhill.

How to

1. Remove all old rim strips or tape and clean the rim.

2. Make sure the rim is clean and dry before applying the tape.

3. Get the tape from the packet and line it up from the opposite side of the valve.

4. Start by unwinding a small amount of the tape and pressing it down using your thumb or finger to hold pressure down.

5. Continue to hold while you pull back on the tape and stick down tight once you have a few cm on the tape will stick and holding is no longer needed.

6. Continue the entire way around the rim (if it has a big concave in you can pull and wiggle the tape to fill any edges)

7. Overlap the tape by roughly 10 – 15cm

8. Leave a small amount unstuck so that you can cut the remainder off

9. Once cut sketch and pull the tape down to create a seal

10. Go around the rim with your thumb to make sure there are no air pockets or messed areas.

11. Once you are happy with how it looks using a small pin locate the valve hole and cleanly pierce the tape ready for the valve

12. Grab your tubeless valve and remove the lock ring and o ring

13. Chose the right rubber fitment for your rim tape and insert the valve into the rim

14. Refit O-ring and Lockring making sure you lock the valve in (don’t go too tight or could damage the rubber)

15. Re-fit your tire of choice careful not to damage the tape (by using tire levers etc)

16. Inflate tire to create a fit (should hear some popping around the rim)

17. Release Air and remove valve core using the spare valve cap

18. Grab the sealant pouch and give it a shake

19. Unscrew the cap and fit on the valve in an upright position

20. While holding the pouch spin the wheel down so that the pouch is now upside down

21. Insert the sealant by rolling the pouch down

22. Spin wheel back upright and remove the pouch

23. Reinsert valve core and inflate to your pressure

Our kit options:

• Road (21MM TAPE / 44MM VALVES)

• Road (21MM TAPE / 60MM VALVES)

• XC/Gravel (25MM TAPE / 44MM VALVES)

• DH/Trail/Enduro (30MM TAPE / 44MM VALVES)

• DH/PLUS (25MM TAPE / 44MM VALVES)

What's included:

• 1x 10m roll of Tubeless Rim Tape

• 2x Seal Patches

• 2x Black Tubeless Valves

• 2x Valve caps

• 2x Locking nuts

• 1x Valve core removal tool (doubles as a spare valve cap)

• 3 x Pairs of rubber bases for size choice

• 2x Pouches of No Puncture Hassle Tubeless Sealant